How to Change Oil for a Mercury Outboard
Motor oil is the lifeblood of your Mercury Outboard which lubricates, cools, and removes contaminants from the motor. When you change your motor oil as recommended by Mercury you keep your outboard running in top condition. Boat parts from PartsVu are the best team to get free consultancy to change the oil for a Mercury Outboard and get the best oil online.
Entire Process – change oil for a Mercury Outboard
When you repair your Mercury outboard lower unit, you can comfortably say that your engine will operate well when you go for a day out on the lake. An essential component of keeping an outboard engine maintained is lower unit fuel replacements. An outboard motor’s internal parts are properly lubricated when the oil is changed, and the fluid is also cleared of typical shavings. Additionally, while you’re at it, checking the oil during an oil change will provide information on the condition of the motor’s internal parts.
- Firstly, make very sure that the outboard is level and standing up straight. The top and lower fill and drain plugs must then be located and identified. When removing the bottom drain plug from the outboard, place an oil drain pan underneath it. You must ensure that the oil drain pan is positioned properly to capture the oil draining out since some oil will start to dribble out.
- Once the upper drain cap has been removed, the vacuum that has been created will be released, allowing the grease to easily flow from the Mercury bottom unit. Enable the bottom unit’s oil should entirely drain out. It is possible for this process to finish in 5 to 10 minutes.
- The bottom unit will need to be replaced once all the oil has been entirely removed. Squeeze bottles and tubes are only a couple of the instruments available to refill the oil. Using a squeeze bottle appears to be the simplest method for the majority of folks.
- Place the container or tubes into the bottom drain hole to reload the bottom unit, then carefully press the container to drive the oil into the lower unit.
- Oil should keep being added until it is running easily and bubble-free from the topmost pipe. Replace the upper plug while keeping the bottle or tube in the bottom pug. Insert the drain stopper after swiftly removing the bottle from the hole in the bottom. To reduce the overall quantity of oil lost, it is crucial to complete this as rapidly as possible. There will be some oil loss although if there is just a tiny vacuum. Wipe off any oil that may have gotten on your bottom component and manually adjust the upper and lower drain plugs.
- Just a Mercury motor should be combined with a lower unit gear lubricant designed for marine use. This oil often contains an ingredient with enhanced water demulsibility and corrosion prevention.
The drain plug is on the port side of the hull and below the engine. Place an oil-absorbing pad under it, then remove it with a socket wrench or pliers. Drain old oil into this pad and let it sit for 5 minutes then remove the plug with another wrench or pliers – use caution not to damage any plastic parts while doing this! PartsVu is a leading boat parts that offer the best team for oil replacement and also ensures quality.
1: Identify the oil drain plug on the port side of the boat’s hull, directly below the engine
- Identify the oil drain plug on the port side of the boat’s hull, directly below the engine.
- Use a socket wrench to loosen and remove this plug for access to your outboard engine’s oil pan and bearings (see photo).
2. Place an oil-absorbing pad under the plug and unscrew it using a socket wrench or pliers. The old oil will drain into this pad
To change the oil, you will need to remove the plug from the engine. To do so, place an oil-absorbing pad under the plug and unscrew it using a socket wrench or pliers. The old oil will drain into this pad.
Once you have removed all of your existing oil and replaced it with fresh new gearbox fluid (if applicable), re-insert your new gearbox filter assembly into its place in line with several other components on top of your engine block before tightening everything down securely again with an Allen wrench or hex key—you may also want to use some Plasti-Dip® spray paint if your new part isn’t already painted black so as not to attract dirt during storage until next time when needed again!
3: Dispose of the old oil
- Dispose of the old oil by transporting it to an area that takes care of old motor oil. Check with your local marine center to find out where you can dispose of used motor oil.
- Some areas have programs in place for people who want to recycle their used motor oil, but many others will take care of it for you.
4. Replace the drain plug and tighten it to prevent leaks using a socket wrench or pliers.
- Replace the drain plug and tighten it to prevent leaks using a socket wrench or pliers.
- Don’t over-tighten it, as this can cause damage to your outboard motor.
5: Taking care of your Mercury Outboard means that it will take care of you, and last longer too
Motor oil is the lifeblood of your Mercury Outboard. It lubricates, cools, and removes contaminants from the motor. When you change your motor oil as recommended by Mercury, you keep it running in top condition!
As an example: if you have a 2000 Outboard with 10,000 hours on it and no maintenance done since new then first thing is to drain all old motor oil out (unless otherwise specified) and then fill it with fresh new stuff only.
Ensure That Your Oil Has The Essential Characteristics
- Good interaction with seals
- Superb water and moisture resistance
- Excellent rust and corrosion control for equipment in both dry and wet environments
- improved cleaning of the gears, joints, and sealing
Now that you’re familiar with how to change the oil for a Mercury Outboard, keep your outboard running smoothly and safely. You can rest easy knowing that you’re taking good care of your precious engine and getting the most out of it! If you have still any confusion then consult with PartsVu. PartsVu is a leading boat accessories company – available to help you in any possible matter including oil changes and oil replacement. Save your money and ensure a good trip.